Time Attendance & Access Control

Edge is the next evolution in access control hardware solutions and time attendance system. A true IP solution that meets the demands of IP-centric environments, Edge provides fully distributed intelligence and decision making right to the door, leveraging the IT infrastructure to the maximum extent possible. Edge Power Comes Through A Single CAT-5 run to the door -- Edge IP Access Solutions run everything at the door, i.e entrance monitoring system. From reader to strike, status to REX. And since each Edge IP Access Solution can utilize PoE (Power over Ethernet) driven right through the CAT-5, separate power supplies and multi-door controllers are no longer required. Edge configurations are exactingly constructed for Host environments as well as single door applications with a wide range of unique benefits that is a complete solution to card door monitoring system and entrance monitoring system.

The HID Vertx product, the V2000 boasts a 32-bit RISC processor running the Linux Operating System, communicating via industry standard TCP/IP protocol, over 10/100 Mbps Ethernet or the Internet is web based access control system and building monitoring system. On-board flash memory allows program updates to be downloaded via the network. The V2000 connects to two access control card readers via Wiegand or Clock-and-Data interface controlling either one or two doors. This architecture takes advantage of the existing corporate LAN and the existing CAT-5 cable. Door network controller is an excellent automatic entry control system and access control premises.

The HID Vertx product, the V1000 boasts a 32-bit RISC processor running the Linux Operating System, communicating via industry standard TCP/IP protocol, over 10/100 Mbps Ethernet or the Internet is web based attendance software that is a complete time attendance solution. On-board flash memory allows program updates to be downloaded via the network. The V1000 connects up to 32 Door/Reader, Input Monitor, or Output Control Interfaces via two independent RS-485 networks, each network having two sets of input connections for optimum system topology. This architecture minimizes the impact on corporate LANs by using only one TCP/IP address for every 32 interfaces, and by handling low-level transactions on the RS-485 network. Master network controller is web based access control system that helps in maintaining on-line attendance control.

The HID Vertx product, the V100 Door/Reader interface connects two access control card readers via Wiegand or Clock-and-Data interface controlling either one or two doors that is security system for office access which access control technology. The V100 features on-board flash memory, allowing program updates to be downloaded via the network. The V100 connects to the V1000 through a high speed RS-485 network that is electronic access system.

The HID Vertx product, the V200 input monitor interface connects up to 16 supervised input circuits that is security system for office which is entry/ exit control system. Each input point monitors and reports normal, off-normal, and alarm states. The V200 features on-board flash memory, allowing program updates to be downloaded through the network. The V200 connects to the V1000 via a high speed RS-485 network that is extremely beneficial as office access security system, access control device and security system technologies.

The HID Vertx product, the V300 output control interface contains 12 latching Form-C relays, which can connect up to 12 devices controllable by simple contact closures, such as logic inputs for process equipment, HVAC and elevator control panels, CCTV switchers, etc. that is access control product used as security system for office access. Loads exceeding 2 A @ 30 VDC should be controlled via interposing relays. The V300 features on-board flash memory, allowing program updates to be downloaded via the network. The V300 connects to the V1000 through a high speed RS-485 network, it is access control solution that is access control equipment.

SmartTOUCH™ is a flexible, highly secure and stylish contact less smart card reader ideal for customers that require a customizable reader for new or existing installations that biometric access control system which is biometric time attendance solution. Smart TOUCH not only verifies the validity of a MIFARE or DESFire card, it also verifies that the person who presents the card is its rightful owner. It is fingerprint attendance system that scans the fingerprint of the card holder and stores it on the secure part of the card. When there is a match between the finger scanned and the template stored on the card, the card data is transmitted through card punching system for attendance. With the addition of PIN, the SmartTOUCH offers a third level of security through card based attendance system and finger print access control system.

Optimized to make physical access control more powerful, iCLASS 13.56 MHz read/write contact less smart card technology from HID provides versatile interoperability and supports multiple applications such as biometric authentication, cashless vending and PC log on security that is extremely useful as web based access control software and Iclass nad Mifare cards. iCLASS smart cards and readers that are actually smart card access control make access control more powerful, more versatile, and most important of all, offers enhanced security through encryption and mutual authentication. At the same time, iCLASS is user-friendly, delivering the convenience, afford ability and reliability of proximity technology for which HID is known worldwide.